61 not categorized PORSCHE 356A REAR BUSHINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 924 1986-88 (includes uncategorized and accessory items) FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection FVD205996003VAG These bushings are made for h&r front sway bars with 25 mm diameters. They are a direct replacement for our part # . These will also work on any bar with a 25-mm diameter. If you would also like to replace the rear, please use part # FVD205996003hag sold as a front set. 1 set needed per car.
$58.30
Make a selection FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection 99333105180 The bushings are made of rubber with an 85-shore hardness value, which is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Sold individually.
From $764.50
Make a selection 99333105280 The bushings are made of rubber with an 85-shore hardness value, which is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Sold individually.
From $764.50
Make a selection P909218 Forged from the highest quality steel, each torsion bar is centerlessly ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. All performance products torsion bars are guaranteed for 3 years against breakage. Note: worn torsion bar bushings will shorten the life of torsion bars. Our 3-year guarantee will remain valid only when bushings are in good condition at time of installing new torsion bars. Sold in pairs. General Fitment924 1976-79924 1980-85 924 1986-88 944 1989-91 944 1985-88 944 1982-85 968 1992-95
$341.99
Make a selection P904784 Forged from the highest quality steel, each torsion bar is centerlessly ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. All performance products torsion bars are guaranteed for 3 years against breakage. Note: worn torsion bar bushings will shorten the life of torsion bars. Our 3-year guarantee will remain valid only when bushings are in good condition at time of installing new torsion bars. Sold in pairs. General Fitment924 1976-79924 1980-85 924 1986-88 944 1982-85 944 1985-88 944 1989-91 968 1992-95
$347.95
Make a selection 90133379303
From $10.10
Make a selection 477411313M This bushing is made for sway bars with a 21 mm diameter. Sold individually. 2 necessary per car.
From $6.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |